Is the NIC built into the motherboard or an add on pcie card?
You could check the journal to see if the logs tell you anything.
Is the NIC built into the motherboard or an add on pcie card?
You could check the journal to see if the logs tell you anything.
You could try taking some packet captures from opnsense and your server while accessing your externally available web server. Reviewing the pcaps might give you some hints on how fix it based on what behaviour you see in the captures.
This is how I would do it also, assuming you aernt passing the NICs through to VMs
Once you change your DNS server in your router, make sure to renew your clients DHCP lease. It may still be using the stale DNS server. On windows verify its using the new DNS server with: ipconfig /all
No issues jumping straight from 37 server edition to 40.
This website has a bunch of great practice “wargames”. You’ll learn a bunch about common linux commands and the different options for them. It also provides you with some great tips on what to google if you get stuck. I reccomend starting with bandit.
+1 for openscad. I switched over from Fusion 360 back when autodesk changed the personal use license in 2020.
It takes a bit to get used to it, but once you’ve made a few parts you begin to see how powerful it can really be.
Its also super lightweight, so you can run it on most systems without any issues. I’ve ran in on a chromebook before.
The only thing I miss about fusion 360 is an easy way to add fillets to parts, that can be tricky in openscad. I use chamfers for the most part though, so I don’t miss it much.
The Culture series by Iain M Banks has an interesting spin on a utopian society.
I get quite a few reccomend actions from the sci-fi/fantasy rss feeds I’m subscribed to. I also get some from suggestions on lemmy.
I like Language Transfer. It’s free and you can download the episodes for offline listening.
deleted by creator
I do this same thing. I have Ubuntu on an external ssd with its own EFI partition. I followed this guide to get it setup and it works great.
A custom router + managed switch is a great way to learn. Studying the fundamentals is also good, but in my opinion it’s not as fun as setting up your own network and learning hands-on.
If you decide to go this route I highly reccomend taking regular backups of your config (and backup again before you change stuff). Part of learning involves breaking things - trust me you will break your network - and in networking that’s one of the best ways to learn. Backups will give you an easy way to restore to a known working configuration.
deleted by creator
A few that haven’t been posted yet:
Yes. A unifi ap connects all my wireless devices to my LAN
Yes its my main router. Everything comes into the laptop across one interface setup as a trunk that includes vlans for WAN, LAN, etc. From there proxmox has a vlan aware linux bridge setup that connects to all the VMs/containers that I run. The VM virtual interfaces get tagged with whatever network I want the host to be part of.
I have a laptop motherboard setup with proxmox running:
This is running on an i5-1135 with 40gigs of memory. If your frugal about how you have stuff setup you can pack alot of services into old laptops.
I’ve had my fw 13 since early Feb 2022. So far, I’ve replaced the hinges and upgraded to a new mainboard. (11th gen i5 to 12 gen i7 when it became my main PC).
I’ve redone the thermal paste on the 12th gen 2 times already to clean the fan out and have not had any problems opening things up. I open it up so often to tinker that the pull loop on the keyboard cable finally broke on me a few weeks ago.
My old mainboard is currently running my entire homlab. Opnsense, pihole, Plex, Kavita, audiobookshelf, foundry vtt, *arrs, unifi controller. I threw it into a 3d printed case and its been running fine without any issues.
I thought about upgrading to the fw16, but it’s too expensive for me to justify it. If I want to game I just plug into my eGPU. I don’t need my gaming system to be ultra portable.
I’ll probably upgrade again when they release a new ryzen mainboard that has USB 4 2.0 support so I can take advantage of the additional pcie bandwidth for my GPU.
I would reccomend the fw13 to anyone who is into customizing PCs or is passionate about repairability in the electronics they own.